Correct use of the most sparking sheller

2022-10-19
  • Detail

Proper use of peanut shelling machine

peanut shelling machine is composed of frame, fan, rotor, single-phase motor, screen (there are two sizes), feeding hopper, vibrating screen, V-belt pulley and its transmission V-belt

after the machine operates normally, put the peanut into the hopper quantitatively, evenly and continuously. The peanut shell is broken under the repeated impact, friction and collision of the rotor. Under the rotating wind pressure and impact of the rotor, the peanut kernels and broken peanut shells pass through a sieve with a certain aperture (the first threshing of peanut uses a large aperture sieve, and the small peels after cleaning are replaced by a small aperture sieve for the second threshing). At this time, the peanut shells and kernels are blown out of the machine by the blowing force of the rotating fan, and the light peanut shells are blown out of the machine. The peanut kernels pass through the screening of the vibrating screen to achieve the purpose of cleaning

I. several requirements for the correct use of peanut sheller

1 Requirements for sheller

① shelling is clean and has high productivity. For shellers with visible cleaning devices, it is also required to have a high degree of cleanliness

② low loss rate and small crushing rate. ③ The utility model has the advantages of simple structure, reliable use, convenient adjustment, low power consumption, certain versatility, and can remove a variety of crops to improve the utilization rate of machines and tools

2. Requirements for peanuts (peeled fruits). Peanuts are suitable for drying and wetting. If they are too dry, the crushing rate will be high, and if they are too wet, the work efficiency will be affected. The compaction force of flowers stored in rural areas is 20 to 30 kg. The fruit is generally dry. In order to make it dry and wet, the following methods can be used

① shelling in winter, spray about 10kg of warm water on 50kg of peel evenly before shelling, and cover it with plastic film for about 10 hours, and then dry it in the sun for about 1 hour to start shelling. The time covered with plastic film in other seasons is about 6 hours, and the rest is the same

② dry peanuts (peels) can be soaked in a large pool. After soaking, they can be immediately taken out and covered with plastic film for about 1 day. Then they can be dried in the sun, and begin shelling after being dry and wet

③ voltage requirements and workplace selection. For single-phase motor to work normally, the voltage must reach its rated voltage. Generally, there is only one transformer in a village in rural areas, and households are scattered. In addition, the wires and circuits used are not very standard, resulting in insufficient voltage for users far away from the transformer. Therefore, the workplace should be closer to the transformer

II. Operation methods and precautions

1 Before use, check whether the fasteners are tightened, whether the rotating parts are flexible, and whether there is lubricating oil in each bearing. The sheller should be placed on a stable ground

2. Before use, check the power supply, and the switch must be in the off position

3. After the motor is started, the rotation direction of the rotor should be consistent with the direction indicated on the machine. First idle for a few minutes, and observe whether there is abnormal noise. Only when the operation is normal, can the peanuts be fed evenly

4. When feeding peanut fruit, it should be even and appropriate, and it should not contain sundries such as iron filings and stones, so as to prevent breaking peanuts and causing mechanical accidents. When the peanuts are covered with the sieve, the rice outlet switch can be turned on

5. Peanuts should be suitable for drying and wetting. If they are too dry, the crushing rate will be high, and if they are too wet, the work efficiency will be affected. Select the appropriate sieve according to the size of peanuts

6. When the peanut shells in peanuts increase, the motor can be moved downward to tension the fan belt. The basic mechanical properties of masonry experimental method standard GBJ 12 sends a signal 9 (9) 0 to control the movement of the actuator from the workstation to increase the blowing volume

7. During operation, people should not stand on the side of belt drive to avoid injury

8. After a period of use, when preparing to store the machine, the dust and dirt on its surface and the remaining grains inside should be removed. The machine should be covered and placed in a dry warehouse to avoid exposure to the sun and rain

9. Remove the belt and keep it separately

10. Clean all bearings with diesel oil and apply butter after drying

11. The transmission part and bearing chamber shall be protected to have sufficient lubricating oil. It shall be cleaned and replaced regularly

Copyright © 2011 JIN SHI